surface in contact
英 [ˈsɜːfɪs ɪn ˈkɒntækt]
美 [ˈsɜːrfɪs ɪn ˈkɑːntækt]
网络 接触表面
双语例句
- Disintegration greatly increases the drug's surface area in contact with GI fluids, thereby promoting drug dissolution and absorption.
崩解大大增加了药物与胃肠液的接触表面积，从而促进药物的溶解和吸收。 - Used to protect surface of refractory materials in direct contact with aluminum liquid, such as runners and spilt coil or protect various steel tools in direct contact with aluminum or zinc liquid.
用于保护与铝液直接接触的流道、分流盘等耐火材料表面，也可用于保护与铝或锌液直接接触的各类铁制工具。 - Sliding friction is independent of the area of surface in contact.
滑动摩擦力于表面接触的面积无关。 - Indirect printing: Process where the printing surface is not in direct contact with the paper, e.g. offset printing, pad printing, etc.
直接电子照像印刷机间接印刷：印版并不直接与纸张接触的印刷方法。例如柯式印刷、移印等。 - It's also independent of the surface area that is in contact with this incline which is equally nonintuitive.
与质量无关，还与面积无关，与接触面积无关这一点，也很不可思议。 - Liquid fire also burn only when the surface of the liquid is in contact with the air.
液体燃料也只有在其表面接触空气时才会燃烧。 - This metal surface, placed in contact with the water, will heat the water.
这些金属表面和水接触，这样就可以加热水。 - Electrical characteristic test and surface modification in Contact mode of STM using I-Z curve
利用I-Z曲线的STM接触模式的电学测量和表面改性研究 - The Pair of Hardness on Gear Teeth Surface in Design According to Equal-Contact Fatigue Strength
按等接触疲劳强度设计的齿轮齿面硬度配对 - For the devices made from sintered Al electride the semiconducter surface concentration in the contact region between Al and Si is approximately 10~ ( 18) r/ cm~ 2 which has no distinct relationship with the original surface concentration.
采用烧结铝电极工艺形成的器件，铝硅接触处半导体表面浓度约为10~（18）个/cm~3，与原始表面浓度无明显关系； - The control of flatness and surface roughness in cold strip rolling is a theory contact practical problem, being the important factors in determining the quality of cold rolled strip flatness and control anneal felt.
冷轧薄板板形和表面粗糙度控制是一个理论联系实际的课题。它既是关于冷轧薄板的板形质量水平，也是控制退火粘结的重要因素之一。 - It is in this model that the influence of lubricant on stress intensity factors of surface initial fatigue lean crack in rolling/ sliding contact has been analyzed through using the collapsed 8 node quadrilateral isoparametric elements and numerical extrapolated method.
利用该模型，通过使用基于蜕化奇异等参元和数值外插法的K因子计算方法，分析了滚滑动接触工况下摩擦及油压对表面斜裂纹尖端应力强度因子（SIF）的影响。 - Surface Corrosion in damp air of the bimetal electrical contact rivet head ( Ag-CdO/ Cu) used in low voltage electric apparatus was studied in this paper.
研究了潮湿大气对低压电器用铆钉触头（Ag-CdO/Cu）表面的腐蚀行为。 - The Way How to Find Contact Surface in the Contact Analysis
接触分析中一种确定接触面的方法 - The rolling contact theory of three-dimensional elastic bodies with non-Hertz form is utilized to determine the normal pressure and tangential traction on the contact surface of wheels and rails in rolling contact.
根据确定的轮轨接触几何参数和轮轨接触界面之间的蠕滑率，利用非Hertz滚动接触理论分析计算了锥型轮对和钢轨滚动接触斑作用力的分布。 - In this paper, by using boundary element method and applying a load distributed according to Hertz law on tooth profile, the contact stresses on surface and in body of a spur gear tooth near contact area have been calculated.
本文应用边界元方法，采用在齿廓上按赫兹分布的载荷，直接计算了在接触区附近齿表面和齿体内的真实接触应力。 - The relationship between workpiece ground surface colour and grinding temperature in contact zone has been established under strictly controlled experimental conditions.
本文在严格控制的实验条件下，建立了磨削弧区温度同试件表面烧伤色之间的对应关系； - Influence of lubricant on stress intensity factors of surface lean crack in rolling/ sliding contact
润滑油对接触表面斜裂纹尖端K因子的影响 - Fast Computation of Surface Deformation in Lubricated Contact
润滑接触中弹性变形的快速数值计算 - In the course of friction and wear, the debris produced by M-UHMWPE and LLDPE transfer to the worn surface exits in the contact surface, which act as anti-friction and wear-resisting agent.
在摩擦过程四川大学褚项I学位论文中，M一UHMwPE和LLDPE向磨擦界面转移产生的磨屑分布于摩擦界面，起到了减摩耐磨剂的作用。 - Effect of uneven surface on temperature distribution between wheel and rail in rolling contact
表面不平顺对轮轨滚动摩擦温度场的影响 - Then, it is analyzed how to choose suitable element models and material types for dam concrete and abutment rock, how to set up simulation model for abutment stability analysis, and especially how to simulate slip surface in abutment with ANSYS contact model.
接着，对拱坝坝体混凝土和坝肩岩体应采用的单元模型和材料类型进行分析，建立了拱坝坝肩稳定的仿真分析模型。研究了ANSYS中采用接触模型对坝肩滑动面进行模拟的方法。 - The friction between half metal friction materials and metals lies in the surface transmutation and adhesion in the contact area.
半金属摩擦材料与金属对偶的摩擦起源于接触区附近的表面形变和粘着。 - On the Surface Dimple Phenomena in Thermal Elastohydrodynamic Lubrication Elliptical Contact
热弹流润滑椭圆接触区内表面凹陷现象的研究 - The simulation results show that: in the nano-cutting process of single crystal copper, the dislocation formed in the nanostructure surface and extended. In the tool and workpiece contact area, the stress become higher.
仿真结果表明：单晶铜的切削过程中，在刀具附近的构件表面形成位错并扩展；在刀具和工件接触的部位应力较高；切削过程中，纳构件原子的有序度降低。 - The amount of deformation and tooth contact line stress curves are extracted from the finite element calculation results. That is used to understand the contact stress distribution of the whole tooth surface in the process of contact. And the main areas of modification are determined.
提取了有限元计算结果的变形量、全齿面接触线应力曲线图，以了解全齿面在整个接触过程中的应力分布情况，确定修形的主要区域。 - But the surface quality and deep drawability of product should be improved. Research shows that the surface quality and deep drawability should be in close contact with texture.
但是产品的表面质量和深冲性能有待于提高，研究表明表面质量和深冲性能都与织构有密切联系。 - However, the physiologic function of FR in adult tissues has largely remained a mystery since, in addition to its narrow tissue distribution, FR is predominantly expressed on the apical ( luminal) surface of polarized epithelial cells where it is not in contact with circulating folate.
然而FR在成体组织的生理功能仍然未知，除了因为FR组织分布范围窄，还因为它主要表达在极化上皮细胞的顶部（腔面），而那里不会接触循环中的叶酸。 - When cartilage surface was involved in contact area, corresponding contact stress and pore pressure presented a stale variation, but fluid velocity and contact displacement were both influenced by contact pairs.
当软骨表面处于接触区域，其接触应力、孔隙压力有着稳定的变化，流体速率和位移受接触副的影响较大。 - Workpiece surface laser micro-machining burrs, when two solid surfaces in contact, the actual contact part account for only a very small area of apparent specific gravity.
工件表面激光微加工后产生毛刺，当两固体表面相接触时，实际相接触部分只占表观面积非常小的比重。